How to Fix solid red light on genie garage door opener

0 0
Read Time:5 Minute, 44 Second

Are you having trouble to open or close your Genie model 7055 garage door? You have seen a solid red light on genie garage door opener remote! Now you are thinking why is there a red light on my Genie garage door opener? Solid red lights mean bad board. You can reset the limits the way you know how and see if it works.

In this blog, we will discuss how to reset solid red light on genie garage door opener. We will also discuss if one Garage Motion Sensor Light is red and one is green.

Possible Reasons: Why is the flashing red light on Genie garage door opener?

Possible reasons for a flashing red light on a Genie garage door opener:

  • Most common cause is misaligned or obstructed safety sensors. Ensure it’s clean, free of debris, and aligned.
  • Check the wires connecting the sensors and motor.
  • Check the opener is plugged in and getting power.
  • Sensors or motors broken: Less likely, but may need a tech to fix.
  • Some Genie models have improperly set travel limits.
  • A faulty photoelectric sensor: Clean or adjust it, if necessary.

After you’ve tried basic troubleshooting, consult your owner’s manual or contact Genie support for specific model advice.

Troubleshoot: solid red light on genie garage door opener

Why is there a red light on my Genie garage door opener? A solid red light on Genie garage door opener can indicate a couple of issues. It depends on the specific model.

Here are the most common causes and how to fix them:

solid red light on genie garage door opener

Incorrectly set travel limits:

It’s most likely this is what’s causing the solid red light on Intellilift, ChainDrive, and Aladdin models. 

A door’s travel limits determine how far it can open and close. They’ll stop working incorrectly.

6 Simple Steps to Set Travel Limits:

  1. Locate the Learn/Program button on the motor unit. It’s usually a small button with an LED light next to it.
  2. Press and hold the Learn/Program button until the LED light changes from slow blinking to solid.
  3. Move the garage door to the fully closed position manually.
  4. Press and hold the Learn/Program button again until the LED light blinks rapidly.
  5. Move the garage door to the fully open position manually.
  6. Press and hold the Learn/Program button until the LED light turns off.

Now that the travel limits have been set correctly, and the solid red light should disappear.

Faulty Infrared Sensors:

These are the small beams of light located on either side of the garage door opening. The door won’t close if something’s blocking it. A dirty sensor, an out-of-alignment sensor, or malfunctioning sensor can cause the solid red light.

What is the Solution to Faulty Infrared Sensors?

  • Use a soft, dry cloth to clean the lenses of the photoelectric sensors.
  • Check that the sensors are aligned. It’s best if they’re level and facing each other.
  • You might need to adjust the brackets if the sensors are still misaligned. You can find specific instructions in your owner’s manual.
  • You might need to replace the sensors if they’re dirty or misaligned.

Power Outage or Low battery:

The solid red light might go off if there’s been a power outage or if the wall control unit’s battery is dead.

What is the best way to fix a power outage?

Plug in and power up the garage door opener. You may need to replace the battery in the wall control unit.

A defective motor or control board:

There’s a chance a faulty motor or control board could cause a solid red light. It’s still on after you’ve tried all these troubleshooting steps, so you should call a garage door technician.

How do you hard reset a Genie garage door opener?

You can hard reset your Genie garage door opener to fix persistent issues or start fresh if you want to erase all programmed settings. 

Your model may have different steps. There are two common ways to use Genie:

Method 1: New Genie Openers (Intellilift, ChainDrive, Aladdin)

  • Find the Learn/Program button on the motor unit. It’s usually a small button with an LED light next to it.
  • Press and hold the Learn/Program button until the LED light turns blue. This usually takes around 5 seconds.
  • Once the LED light starts flashing, release the button.
  • The LED light will turn solid blue after you hold the Up and Down buttons (on the motor unit). This usually takes around 5 seconds.
  • Release both buttons. You’ve hard reset the garage door opener and erased all the settings, including remotes and keypads.

Method 2: Old Genie Openers (600/800 Series)

  1. Plug in your garage door opener and unplug it.
  2. Remove the wiring from terminals 1 and 2 on the far right (labeled with a minus and plus sign). The orange tabs above the terminals need to back down gently.
  3. Plug the unit back into the power outlet.
  4. Press and hold the Learn Code button (on the motor unit) until the red flashing light stops blinking to clear the wireless devices. This usually takes around 10 seconds.
  5. Hold both Set buttons (on the motor unit) for 10 seconds to clear the limit settings. The LED light on the unit should then flash 3 times.
  6. Set the garage door’s opening and closing limits. Refer to your owner’s manual for specific instructions on this process.

Read Also: Common Exterior Garage Light Issues And How To Troubleshoot Them Now.

Why is one garage door sensor is red and one is green?

The red sensor is likely malfunctioning or not aligned with the green one. It could stop the garage door from closing since it expects a clear path from both sensors.

Should both Genie garage door sensors be green?

I think this is the ideal situation. Both sensors are aligned, unobstructed, and communicating properly, indicating safe garage door operation.

What does it mean when one garage door sensor is green and the other is yellow?

That’s usually a sign of misalignment. The yellow sensor sends the beam, but the green sensor isn’t receiving it properly. You will check, make sure the sensors are aligned directly with each other. Connect the sensors securely and make sure the wires aren’t damaged. Clean both sensor lenses.

Why is one garage door sensor green and the other orange?

This isn’t common for Genie openers. Orange usually indicates a specific error code depends on the model. You can troubleshoot your orange light in your owner’s manual.

Read Also: Garage Door Sensors Not Working? Here’s How To Fix

In conclusion, a solid red light on Genie garage door opener might alarm you, but don’t worry! You now know how to fix common issues involving sensors, limits, and power. You will check company manual or consult Genie professional.

Happy
Happy
0 %
Sad
Sad
0 %
Excited
Excited
0 %
Sleepy
Sleepy
0 %
Angry
Angry
0 %
Surprise
Surprise
0 %

Author Info

Related Post

Average Rating

5 Star
0%
4 Star
0%
3 Star
0%
2 Star
0%
1 Star
0%

Leave a Comment